Printer Driver For An Adp Laser Station 1920 Latest

By Lawrence

Printer Driver For An Adp Laser Station 1920 Install Update

This guide, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. All rights are reserved.

Copying or other reproduction of all or part of this guide, any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited. This document defines the terms and conditions under which the software is being licensed to you by IBM. If you do not agree with the terms and conditions of this license, then within 14 days after your acquisition of the device you may return the device for a full refund.

Typeface Trademark Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation. B Connecting the Printer to the Computer C-1 Appendix C Glossary Introduction The Kyocera Mita page printer has many extremely desirable features.

It was designed to make a contribution to a cleaner environment as well as to represent the latest generation of page printer technology. This section contains the following subsections. Approximately sheets can be loaded into the paper cassette, and about sheets can be loaded into the MP tray. Wide variety of print media As well as standard paper, the printer will print on transparency, labels and other types of special purpose media. Copies of the document are printed using the stored data.

The electronic sort function can be used for much faster printing. CompactFlash card slot for option fonts, macros, forms, etc. Chapter 2 Paper Selection This chapter explains the types of paper that can be used with the printer. Chapter 3 Maintenance This chapter explains how to replace the toner container, waste toner box, and how to care for your printer. Indicates tips or advice useful for operation.

Note Indicates situations that are potentially hazardous to the human body or devices. Caution Indicates situations that are potentially extremely hazardous to the human body or devices. Warning Indicates operations that can be performed or are effective only when the required option unit is installed. Chapter 1 This chapter explains the following topics: The message display gives information in the form of short messages. The eight messages listed below are displayed during normal warm-up and printing.

While the printer is processing data, the SIZE indicator indicates the paper size selected by the application software. Indicates that the printer is on-line. The printer prints received data.

Indicates that the printer is off-line. Data can be received but will not be printed. Also indicates when printing is automatically stopped due to occurrence of an error. This menu is the setting menu for administration under the Account Management System and is normally not used. The menu map is usefull as a reference to guide yourself through the menu selection system. The status page is a list of parameters and settings for most basic printer configurations.

You may be required to produce a status page when requesting service to the printer. Printing Test Pages Status Page If you want to check the printer's current status, including memory available and option settings, you can find the information you need on the status page. Press the MENU key. Press the key repeatedly until Print Status Page appears. The following is a sample status page. The numbers below refer to the contents explained on the following pages.

This information shows the firmware version and date of issue of the printer. Printing Test Pages 10 — Interface Information This information shows the default font and the default emulation for all interfaces installed in the printer. Printing Test Pages Service Status Page The service status page contains printer settings information that is more detailed than the standard status page and is therefore for mostly service purposes.

However, since there is a great deal of information available on the service status page that may be helpful to you, the procedure for printing it out is given below.

The default setting is On print. If the setting is changed to Off not print as follows, however, the network interface status page will be printed when the printer status page is printed. Printing out a network interface card status page may not be possible with some network interface cards. A blinking question mark? The message display returns to Ready.

Processing appears, then Ready. The printer prints a list of fonts with a short sample and font ID number for each font.

Received Data Dumping It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. The paper size setting for the paper cassette is completed. When using non-standard size paper, read the next section to set the paper size from the operator panel.

Setting a custom size from the Operator Panel Set the size of the paper loaded in the paper cassette into the printer from the printer operator panel. If option paper feeders are added, Cassette 1 Size will appear for the standard paper cassette and Cassette 2 Size, Cassette 3 Size, and Cassette 4 Size will appear for the option paper feeders. Selecting the Unit of Measurement Then, use the following procedure to set the unit of measurement.

The unit of measurement can be selected between millimeters and inches. The current unit of measurement is displayed the default setting is mm. To print using the custom size set above, define the same custom size on the printer driver. For details, see Operation Guide. A4 Press the key to display the desired MP tray size. The display changes as shown below. Make this setting to match the paper type fed from the paper cassette of the printer.

If the paper type is set correctly, you can perform printing using the media type selection function from the application software printer driver. The factory default setting is Plain. Setting the Paper Type in MP Tray You can automatically select the paper cassette according to the selection made by the application software printer driver.

This menu does not appears when the option envelope feeder is installed on the printer. The following describes the procedure used to set a user-defined paper type for the printer. Eight custom user settings may be registered. After having been set, any of these may be called up when setting the paper type for a paper source. Custom 1 Press the key to display the desired paper type. If the paper type is set to Custom and the option duplexer is installed on the printer, duplex printing can be enabled and disabled.

Option If the paper type is set to Custom and the option duplexer is installed on the printer, you can set whether or not to enable duplex printing as follows. The default setting is Enable. Cassette Mode This is the default mode.

The MP tray acts in the same manner as other paper source. The printer can correctly feed paper from any paper source as you command on the printer driver. The cassette mode provides a faster printing speed than the first mode. You can select from which paper source printing will be performed. If no option units are installed, the only selections are the paper cassette and MP tray of the printer.

If option paper feeders are installed, they can also be selected using the manner described below. The output tray changes as shown below. Under the default setting of Off, the paper size of the paper source is matched to the paper size formatting the jobs.

If these differ, a corresponding error message is displayed. To change the emulation mode, proceed as follows: Press the key repeatedly until Emulation appears. One of the emulation modes shown below appears, indicating the current emulation. The alternative emulation can be selected using the operator panel.

The printer can print error descriptions when printing error occurs during KPDL emulation. You can select the default font for the current interface. In addition to the internal fonts, all fonts that are downloaded to the printer memory, or fonts stored on a CompactFlash card, Microdrive, or option ROM, can be selected as the default font.

The message display changes to that show below. Pagination Default Font Size The following procedure determines the size of the default font. If the default font is a fixed font such as Courier or Letter Gothic, the character pitch can be changed instead of the font size. For example, to change the type of Courier, proceed as follows: Code Set You can change the character code set.

Available character code sets vary depending on the current font. Pagination Number of Copies You can set the number of copies to be printed of each page for the current interface.

Printer Driver For An Adp Laser Station 1920

Kyocera FS FS-1920 Operation Manual

This guide, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this guide, any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited. This document defines the terms and conditions under which the software is being licensed to you by IBM. If you do not agree with the terms and conditions of this license, then within 14 days after your acquisition of the device you may return the device for a full refund. Typeface Trademark Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation.

Support & Download

Printer Driver For An Adp Laser Station 1920

Posted by westtex on Aug 03, ADP laser station printer drivers can be found at driverupdate us. Take a look, and enjoy. Posted on Nov 02, I have done a little research for you. Your printer is made by Kyocera. Here is the download link for your model. I hope it works. Posted on Aug 03,

0 thoughts on “Printer Driver For An Adp Laser Station 1920

Leave a Reply

Your email address will not be published. Required fields are marked *